RCModelScout.

DPCAV

GUARDIAN 2D/3D INERTIAL STABILIZER (STANDALONE MODEL)

Q: Why do I need the Guardian?, The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation: In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control., The Guardian has two submodes for 3D flying: In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc. In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions., Q: I Fly FPV. Is the Guardian for me?, Q: Will the Guardian work with my model?, Q: How do I install the Guardian?, Q: How do I configure the Guardian?, Q: How does the Guardian work?, Q: What sets the Guardian apart from other Stabilization systems out there?, *Note: Using the PC software will require a common Micro-USB cable. Most likely you already have one of these, but it not then they are available from your local electronic/computer store.,

DPCAV

LOST MODEL ALARM

Instructions:,

DPCAV

900MHZ A/V RECEIVER, DELUXE MODEL WITH COMTECH TUNER

The receiver requires a common 2.1mm barrel type DC power cord (available separately). It's not included so that you can choose what is best for your installation. We offer several different types and they can be found here:click here, The receiver requires a common 2.1mm barrel type DC power cord (available separately). We offer several different types and they can be found here:click here, half-wave dipole is a popular antenna choice and can be purchased with the receiver as an option. We offer other 900Mhz antennas too:click here., Important note: The DC input connector is a 2.1mm barrel style connector that is center (+) positive. Reversed voltages will damage the receiver!,

DPCAV

900MHZ A/V RECEIVER, DELUXE MODEL

; It is an efficient dipole design and NOT a simple wire whip. You can choose to omit the dipole antenna and apply the savings to a different antenna. Of course we offer other 900Mhz antennas, so please have a look:click here.,

DPCAV

900MHZ A/V RECEIVER, STANDARD MINI-MODEL

The receiver requires a common 2.1mm barrel type DC power cord (available separately). It's not included so that you can choose what is best for your installation. We offer several different types and they can be found here:click here, Important note: The DC input connector is a 2.1mm barrel style connector that is center (+) positive. Reversed voltages will damage the receiver.,

DPCAV

FY-30A PRO R/C INERTIAL STABILIZER SYSTEM

Sold Out:, No longer available., How it works:, , Applications:, , The FY30A can be used in the following fixed wing models:, , Compare FY-30A to FY-20A:, Click Me!, Instruction Manual:, Click Me!, Firmware Update Instructions:, Click Me!, Firmware V1.20 Upgrade Files:, Click Me!, Firmware PC Application:, Click Me!, Manufacture's web site:, Click Me!, Sold Out:, No longer available.,

DPCAV

5.8GHZ CLOVERLEAF ANTENNA, RHCP

Manufacture:, Aerial Video Systems, Important: To ensure RF performance do NOT add paint or coat the element lobes (leave the factory applied finish as-is). The elements should not be allowed to rest against any structures. Do not bend or deform the elements., NOTE: Some FPV model installations may need an extension to ensure the antenna is away from nearby surfaces.,

DPCAV

5.8GHZ BLUEBEAM ANTENNA SYSTEM, RHCP

This 5.8GHz antenna system contains TWO antennas:, One for the transmitter and one for the receiver., If you are looking for replacements then we also sell them individually, as follows:, , Manufacture:, Aerial Video Systems, Important: To ensure RF performance do NOT add paint or coat the element lobes (leave the factory applied finish as-is). The elements should not be allowed to rest against any structures. Do not bend or deform the elements., NOTE: We offer very low-loss extension cables that are specifically designed for the BlueBeam antenna system. Some FPV model installations may need an extension to ensure the antenna is away from nearby surfaces.,

DPCAV

PANDORA PAN & TILT KIT

DPCAV

900MHZ PRO-SERIES A/V TRANSMITTER, 500MW

For convenient installation, the TX905-PRO has a JST female power cable (compatible with several of our 3-cell LiPO batteries) and servo-style connectors on the camera and microphone cables. We've made it as ready to use as we could. Just add your compatible camera, battery, and A/V receiver (not included). Plus, a variety of optional accessories are available to make your installation as simple as possible:Click Me!, We also offer high quality 900MHz A/V receivers that work great with this transmitter. So if you don't already have a compatible receiver then be sure to check them out:click here, Non-USA (export) model has four RF channels:, 910MHz, 980MHz, 1010MHz, 1040MHz, Notice: Due to its high RF power, using the TX905-PRO in the USA and other countries will require an amateur/ham radio license (some countries may forbid its use). It is your responsibility to ensure that its use meets the requirements imposed by your government’s RF spectrum regulations. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them.,

DPCAV

900MHZ A/V TRANSMITTER, 500MW

Non-USA model has four RF channels:, 910MHz, 980MHz, 1010MHz, 1040MHz, Important note: The DC input connector is a 2.1mm barrel style connector that is center (+) positive. Reversed voltages will damage the receiver., Notice: Due to its high RF power, using the TX9-500 in the USA and other countries will require an amateur/ham radio license (some countries may forbid its use). It is your responsibility to ensure that its use meets the requirements imposed by your government’s RF spectrum regulations. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them., We offer 900MHz A/V receivers that work great with this transmitter. So if you don't already have a compatible receiver then be sure to check them out:click here,

DPCAV

1.3GHZ A/V TRANSMITTER, 300MW

Non-USA model has four RF channels:, 1240MHz, 1280MHz, 1320MHz, 1360MHz, Important notes: The DC input connector is a 2.1mm barrel style connector that is center (+) positive. Reversed voltages will damage the receiver. NEVER operate the transmitter without an antenna or it may be damaged and warranty voided. Please see the instruction manual for more information., Notice: Due to its high RF power, using the TX13-300 in the USA and other countries will require an amateur/ham radio license (some countries may forbid its use). It is your responsibility to ensure that its use meets the requirements imposed by your government’s RF spectrum regulations. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them., We offer a 1.3GHz A/V receiver that works great with this transmitter. So if you don't already have a compatible receiver then be sure to check it out:click here,

DPCAV

IMPORTED ULTRA T-CONNECTOR

DPCAV

DEANS ULTRA T-CONNECTOR, PAIR

DPCAV

MPX SIX PIN CONNECTOR